The same was true for noise complaints. When someone came in with a rap or tick issue the problem was almost always a noisy catalyst or worn rocker shafts - comparatively simple fixes. Only a tiny fraction of noises were from internal motor problems.
Today, with the late Disco motors, those odds have flipped. When a 2003-4 Rover comes in with overheating trouble, the most likely cause is liner or block failure. A noise complaint is more likely to be from excess clearance in the piston-liners (in other words, prematurely worn out.) I've written several essays about how this happens so I won't repeat all that here. The question is . . . what do we do about it?
The solution that has emerged - both here at Robison Service and in the UK - is to rebuild the blocks using flanged liners so the cylinder head seals against the liner, not the block. Then we fit new pistons with proper clearances.
The photo above shows a typical failure. The block cracks at the base of a head bolt bore, between the back of the liner and the water jacket. With the stock liners there is no barrier to prevent combustion gases going round the liner and into the coolant.
The fitment of flanged liners solves that problem by making the liner top the sealing surface. There is no high pressure gas behind the liner, and the cracks are rendered irrelevant.
The photo above shows a flanged liner and a new piston. The o-ring seals the bottom of the liner to prevent coolant dripping into the oil sump in the event of a crack.
This is what a flanged liner looks like installed. As you can see the wide flange covers the entire sealing area of the head gasket.
We can do flanged liners in 4.0, 4.6, and overbore configurations. At this moment (Sept 2012), costs to do a block with flanged liners, new pistons, and all basic machine work in in the $4800 price range. Our American costs are similar to costs from RPI or Turner over in the UK.
We believe this is the only long-term solution to the problems in these late motors, and it provides a substantial upgrade for any older Land Rover V8. However, the liner repair is just the beginning when it comes to engine overhaul . . .
What else do we do when building a motor?
I recommend balancing any engine. Motors like these rely on sophisticated engine electronics to achieve smoothness. That will be considerably improved if the engine is mechanically balanced before assembly.
Front covers and oil pumps have been problematic on these trucks. The pump gears fracture, and eventually the oil pump fails. The result - engine failure from oil starvation. I recommend fitting a new front cover as long as these parts remain available.
Heads are another problem area. We recommend rebuilding the heads. This involved walnut shell blasting to get everything spotless, followed by crack test and a check for warping. Then we fit new guides, redo valves and seats and cut the sealing surfaces perfectly flat. If you're a perfectionist we can also cc the combustion chambers to ensure each cylinder is exactly equal.
This is a rebuilt head. As you can see the sealing surface is cut to a mirror finish. We true these heads to half a thousandth of an inch to minimize the change of gasket failure.
We also rebuild rocker shafts, and swap cams and lifters. Needles to say, every other part is cleaned and inspected before being overhauled, repaired, or replaced. That thinking should also extend to the external accessories like the water pump, injectors, and alternator.
We believe the engines we are building now are substantially smoother and better than what land Rover delivered new.
Till next time
John Elder Robison
J E Robison Service
Springfield, MA USA
Here are three articles about internal problems in the V8s:
V8 engine failures - slipped liners and more - from 2009
Should you rebuild a failed Land Rover motor? I have an article about that situation here that covers the decision process
What's the latest on top hat or flanged liners? This article tells all you want to know about the flanged liner overhaul
Discovery II models also have a problem with frame rust. We first began to see this in the spring of 2014, when we saw several trucks whose rear frames rusted right through over the winter. These vehicles seemed more vulnerable to rust than the earlier models. Read this article to find out why, and what you can do about it.
Are you thinking of restoring a Land Rover? This article shows some of what's involved. This article explains the difference between repair and restoration, two very different processes.
If you drive a Range Rover Sport or LR3, read this story on differential failures
And if your supercharged Rover is losing power - read this
Programming keys for your Land Rover is here
(c) J E Robison Service
John Elder Robison is the founder of J E Robison Service, independent Land Rover specialists in Springfield, MA. John's shop has supported Land Rover owners since 1987. They are experienced at all aspects of service, repair, overhaul and restoration. Find Robison Service online at www.robisonservice.com or on the phone at 413-785-1665.
About the author:
John Elder Robison is the general manager of J E Robison Service Company, independent restoration and Bosch Authorized Car Service specialists in Springfield, Massachusetts. John is a longtime technical consultant to the Land Rover, Porsche, and Rolls Royce Owner's Clubs, and he’s owned and restored many of these fine vehicles. Find him online at www.robisonservice.com or in the real world at 413-785-1665
Tidak ada komentar:
Posting Komentar